Monday, March 24, 2008

Ikan Bakar Portugis


Lama tak post menu..terjumpa lak kat online so terus copy...


IKAN bakar ala Portugis menjadi kegemaran ramai. Selain mudah disediakan, ia juga harum dan memikat selera. Anda boleh sediakan dan bungkus untuk dipanggang atau barbeku di tempat perkelahan. Ia memang sesuai sebagai hidangan dengan nasi.

Ikan yang sering menjadi pilihan ialah ikan pari jenis kecil. Selain itu, ikan bawal atau kembung. Pastikan anda mengelar isinya supaya kuah mudah meresap. Jika menggunakan ikan besar, anda boleh bungkus sepotong untuk hidangan seorang saja. Oleh kerana kuahnya masak sekali dengan ikan, kemanisan ikan tersebut tetap kekal.

Cara memasak dengan membakar atau memanggang juga lebih menyihatkan daripada cara menggoreng dengan minyak yang banyak. Malah, ia juga tidak mengandungi santan yang boleh memudaratkan kesihatan jika dimakan terlalu kerap.

Jika tidak sukakan bau daun limau purut, boleh gunakan daun kunyit, daun kemangi atau daun jintan. Ia akan mewangikan hidangan dan pasti membuka selera sesiapa saja. Keharuman herba ini juga dapat menghilangkan bau hanyir ikan. Anda juga boleh lumur ikan dengan jus limau nipis seketika supaya baunya hilang. Kemudian barulah dibasuh dan dilumur pula dengan garam.

Masakan ini menggunakan pes cili atau cili boh. Anda boleh membuatnya sendiri di rumah dengan mengisar cili kering hingga halus. Pastikan cili dibuang bijinya terlebih dulu dengan cara menggunting serong. Rendam di dalam air mendidih selama 20 minit. Kemudian barulah dikisar dengan garam dan air masak. Dengan meletakkan garam, pes cili tahan lebih lama. Simpan di dalam bekas bertutup yang diletak di dalam peti sejuk.

Cili merah dan cili padi juga dimasukkan sekali. Biji cili merah hendaklah dibuang untuk mengurangkan pedasnya. Jika anda suka lebih pedas, tambah cili padi atau boleh hiriskan dan taburkan di atasnya sebelum dipanggang.

Jika hendak dimasak di atas bara api, tidak perlu dibungkus dengan foil. Begitu juga sekiranya anda masak di atas kuali leper atau kuali capati. Kuali begini tebal dan dapat mengekalkan kepanasan. Semasa memanaskannya, pastikan api besar. Kemudian barulah diperlahankan apinya.

Jika memanggang dengan daun pisang sahaja (tanpa foil), pastikan ia dua lapis. Kemudian sapu bahagian luarnya dengan sedikit minyak. Ini dapat menghalang daun tersebut menjadi hangus. Sekiranya memanggang dengan daun pisang, bau ikan lebih harum.

Untuk mengekalkan kesegaran daun pisang, bungkus dengan suratkhabar. Kemudian letak di atas beg plastik dan bungkus kemas. Simpan di rak bawah di dalam peti sejuk. Daun pisang untuk membungkus kuih-muih perlu dilayur terlebih dulu. Selain melayur di atas api perlahan dengan memegang kedua-dua hujung daun pisang, anda juga boleh merendamkannya di dalam bekas berisi air mendidih sehingga lembut.

Bagi yang tidak suka menggunakan jus limau nipis, boleh digantikan dengan jus limau kasturi atau jus lemon (limau susu). Ambil hanya satu camca besar jus. Jika suka masam bolehlah ditambah. Selain itu, boleh juga gunakan air asam jawa yang pekat. Jangan sesekali lupa untuk mencampurkan gula supaya rasa masamnya dapat diseimbangkan.

Sekiranya anda mahu mengubahsuai resipi, anda boleh gunakan dada ayam tanpa tulang. Ia mesti dikelar terlebih dulu supaya mudah masak. Jangan lupa tambah satu cm halia ke dalam bahan kisar. Halia dapat mengurangkan bau ayam yang mungkin kurang enak pada sesetengah orang.

Belacan yang dipanggang di atas api atau digoreng dalam minyak yang sedikit akan mengharumkan masakan. Ia juga tahan lebih lama berbanding dengan belacan yang tidak digoreng. Bagi yang tidak sukakan bau belacan mentah, boleh menggunakan serbuk belacan yang dijual di dalam botol.

Jika mahukan ikan atau ayam lebih garing, buka bungkusan pada penghujung lima hingga lapan minit selepas memasak. Pastikan memasang gril (elemen pemanas bahagian atas). Ini boleh dilakukan jika anda memanggang di dalam ketuhar.

Ikan akan masak jika bahagian matanya bertukar menjadi keputih-putihan. Sajikan dengan segera kerana isi ikan menjadi liat (terutama bila sejuk) jika terlebih masa memasaknya. Ikan seperti pari kecil atau dikenali sebagai tuka tidak memerlukan masa yang panjang untuk masak kerana isinya yang nipis.

Seandainya anda membuatnya dalam kuantiti yang banyak, setelah dibungkus, simpan di dalam bekas bertutup yang diletak di dalam peti sejuk. Ia tahan selama 48 jam. Rasa ikan juga menjadi lebih sedap kerana bumbunya sudah meresap ke dalam ikan tersebut.

SELAMAT MENCOBA....

Peazzzz...



Sunday, March 23, 2008

Danielle bersama Suria FM

Petang ni Diana Danielle aka nyanyai....akan memperdengarkan suara nya di SuriaFM Rancak RoadTour 2008...Pi jangan tak pi...kalau ada kelapangan...Danielle, Pak Tam tak dapat nak pi Mak Tam tak sihat....sorry...nyanyi betul betul tau....tunjuk bakat tu....pastikan lagu petang semalam didendangkan ngan syahdu sekali...biar naik bulu roma sapa yg dengar yekkkkkkkk.....



Untuk info lanjut layari lah link di bawah ni

http://www.suriafm.com.my/rancak/rancak_road_tour_2008.asp

Peazzzz....

Wednesday, March 19, 2008

SENARAI PENUH KABINET BARU KERAJAAN MALAYSIA

Berikut adalah senarai penuh barisan Kabinet Malaysia yang telah di umumkan oleh YAB. DAtuk Seri Abdullah Ahmad Badawi :-

PM announces new Cabinet line-upPUTRAJAYA: Prime Minister Datuk Seri Abdullah Ahmad Badawi on Tuesday a 27-seat Cabinet line-up.More than half of the ministers are new faces.They are Ahmad Zahid Hamidi, Zaid Ibrahim, Amirsham Aziz, Ismail Sabri, Douglah Unggah, Ong Tee Keat, Ng Yen Yen, Noh Omar, Zin Mohamed, Liow Tiong Lay, Ahmad Shabery Cheek, Shahrir Samad, Muhammad Muhammad Taib, Ong Ka Chuan, and Shaziman Abu Mansor.

The full list:

Prime Minister
Datuk Seri Abdullah Ahmad Badawi.


Deputy Prime Minister
Datuk Seri Najib Tun Razak.


Ministers in the Prime Minister's Department
Tan Sri Bernard Dompok
Datuk Seri Nazri Aziz
Datuk Ahmad Zahid Hamidi
Datuk Mohd Zaid Ibrahim
Datuk Amirsham Abdul Aziz
Deputy Ministers in the Prime Minister's Department
Datuk Johari Baharom
Datuk Dr Masitah Ibrahim
Datuk K. Devamany
Datuk Hassan Malik

Finance Minister
Datuk Seri Abdullah Ahmad Badawi
Second Finance Minister
Tan Sri Nor Mohamed Yakcop
Deputies
Datuk Ahmad Husni Hanadzlah
Datuk Kong Cho Ha

Defense Minister
Datuk Seri Najib Tun Razak
Deputy
Datuk Wira Abu Seman Yusop

Internal Security and Home Affairs Minister
Datuk Seri Syed Hamid Albar
Deputies
Datuk Chor Chee Heong
Senator Wan Ahmad Farid Wan Salleh

Housing and Local Government Minister

Datuk Ong Ka Chuan
Deputies
Datuk Robert Lau
Datuk Hamzah Zainuddin

Public Works Minister
Datuk Mohd Zin Mohamad
Deputy
Datuk Yong Khoon Seng

Energy, Water and Communications Minister
Datuk Shaziman Abu Mansor
Deputy
Datuk Joseph Salang Gandum

Agriculture and Agro-based Industry Minister
Datuk Mustapa Mohamed
Deputy
Datin Paduka Rohani Abdul Karim

International Trade and Industry Minister
Tan Sri Muhyiddin Yassin
Deputies
Loh Wei Keong,
Datuk Jacob Dungau Sagan

Foreign Affairs Minister
Datuk Seri Dr Rais Yatim
Deputy
Tunku Azlan Abu Bakar

Education Minister
Datuk Seri Hishammuddin Hussein
Deputies
Datuk Wee Ka Siong,
Datuk Razali Ismail

Higher Education Minister
Datuk Khaled Nordin
Deputies
Khoo Kok Choong,
Datuk Idris Harun

Transport Minister
Datuk Ong Tee Keat
Deputy
Anifah Aman

Human Resources Minister
Datuk S. Subramaniam
Deputy
Datuk Noraini Ahmad

Women, Family and Community Development Minister
Datuk Dr Ng Yen Yen
Deputy
Noriah Kasnon

National Unity, Culture, Arts and Heritage Minister
Datuk Shafie Apdal
Deputy
Datuk Teng Boon Soon

Science, Technology and Innovation Minister
Datuk Dr Maximus Ongkili
Deputy
Fadilah Yusof
Entrepreneurial and Cooperative Development
Minister
Datuk Noh Omar
Deputy
Datuk Saiffuddin Abdullah

Natural Resources and Environment Minister
Datuk Douglas Unggah Embas
Deputy
Datuk Abu Ghapur Salleh

Rural and Regional Development Minister
Tan Sri Muhammad Muhd Taib
Deputy
Tan Sri Joseph Kurup

Domestic Trade and Consumer Affairs Minister
Datuk Shahrir Samad
Deputy
Jelaing Mersat

Plantation Industries and Commodities Minister
Datuk Peter Chin Fah Kui

Deputy
Senator A. Kohilan

Youth and Sports Minister
Datuk Ismail Sabri Yaacob
Deputy
Wee Jack Seng

Health Minister
Datuk Liow Tiong Lai
Deputy
Datuk Dr Abdul Latiff Ahmad

Information Minister
Datuk Ahmad Shabery Cheek
Deputy
Datuk Tan Lian Hoe

Tourism Minister
Datuk Azalina Othman
Deputy
Datuk Sulaiman Abdul Rahman Abu Taib

FT Minister
Datuk Zulhasnan Rafique
Deputy
M. Saravanan

Adalah di harapkan perlantikan tersebut akan lebih memantapkan lagi pentadbiran Kerajaan Malaysia yang di terajui oleh YAB Dato' Seri Abdullah Ahmad Badawi

Peazzzz....

Monday, March 17, 2008

Tuesday, March 11, 2008

Sekadar Rujukan..PSU

Aku pun tak tahu gak...tapi aku dah boleh hidupkan kipas dia...so rasanye pass ni nak try connect pada radio kereta ada power tak...

Ni kat bawah ni carta color code dia...

Dan kalau rajin nak mentela'ah boleh baca yang ni...

Desktop Power Supply from a PC

(See the narrative and disclaimer at the bottom of the page)

A completed 145 watt ATX power supply with switch, binding posts, labels and feet. Notice the zip ties in the ventilation slots
that hold the load resistor.

This ATX PS board has leads for +5 (RED), -5 (WHITE), +12 (YELLOW), -12 (BLUE) volts, Ground (BLACK) and switch (GREEN). Dell power supplies manufactured between 1996 and 2000 do not follow the industry standard pinout and color codes. The fan has also been unplugged for better viewing. Since this PS was converted for use in the logic and robotics labs, the selected voltages were tapped. Other users may want combinations of +3.3 V (ORANGE), +5 V and/or +12 V if they are converting one of the newer supplies. For R/C applications, the 5 volt output can also serve as a desktop source to drive receivers and servos. If used as a power source for the micro and sub-micro servos, you must be careful not to drive the servo to either endpoint to avoid stripping the smaller gears in these units. Most standard servos have sufficiently robust gear trains and will simply stall if pushed to the mechanical stops..

Measured voltages on this particular PS (1996 P5-100 MHz Gateway) were about 5.15 and 11.75 volts. The remaining leads have been clipped off at the circuit board.

View of the case top with fan, binding posts and switch. The switch (SPST) and binding posts are available at Radio Shack or other electronics suppliers.


Power supplies in today's computers are known as SWITCHMODE or Switching Mode power supplies and require a load to continue to operate after being switched on (the term switching mode actually applies to the technique of A/C to D/C conversion and not to the power up action). This load is provided by a 10 watt, 10 ohm wire wound load resistor (sandbar - about $0.80 at Radio Shack) across the +5 volt supply. Some inexpensive power supplies may fail if forced on without a load. The sandbar has been zip tied to the case with a small amount of heat sink compound applied. Without cooling, the resistor will get very hot and may fail prematurely. With this arrangement, the resistor will remain barely warm to the touch.

Be warned that many of the heat sink greases can be quite toxic and any excess should be cleaned up and disposed of properly. Also be sure to thoroughly clean your hands and tools after use. While most heatsink compounds are rated to 160 to 170 C, some may dry out over time and their effectiveness will diminish -- a periodic check for good contact between the case and resistor is a recommended practice.

Additional comments


Disclaimer: The information presented should not be considered a "HOWTO" article, but merely a documentation of my conversion process. Modern PC Power Supplies can produce high output current levels that may cause internal overheating in the PS or damage to devices connected to them. Any individual attempting their own conversion is cautioned to carefully research their PS specifications and to be mindful of the associated voltages and power. DO NOT work on your opened power supply with it plugged in!!!!
The PS in the picture is a 145 watt ATX salvaged from a 1996 P5-100 MHz Gateway -- I salvage all usable parts from the older PC's before dumping them. This one is set up for a logic lab, hence the +5, -5, +12, -12 volt taps. We also use the +5 to drive servos in the robotics lab. This supply does not have a 3.3 V source, but the newer supplies do. INTEL has continued to modify the ATX specifications to include additional power connectors to support the increased power requirements of the newer motherboards. Before any modification is attempted, you should be sure of the type of power supply you are working with and the output currents being produced at each voltage level. Higher wattage supplies can generate fairly hefty levels of current and may overheat or damage devices attached to them. See the Table of Representative Current Levels for other power supplies.

Wiring coming off an industry standard circuit board will be:

ORANGE +3.3 V
YELLOW +12 V
BLUE -12 V
RED +5 V
WHITE -5 V (May not be present on recently manufactured supplies)
BLACK GND
GREEN POWER-ON (Active high -- must be shorted to ground to force power up)
GRAY POWER-OK What is this??
PURPLE +5 V STANDBY
BROWN +3.3 V REMOTE SENSING Design Guide Update



*** Note that the 1996-2000 Dell's did not completely follow this color coding -- check your voltage levels with a meter before wiring ***


The yellow, red and black wires will likely be grouped together with a clip. Some of the PS's will have a detachable plug for the fan and some will have the fan permanently attached to the circuit board. If the fan is attached, I usually clip the wires then re-solder and cover with heatshrink tubing -- this gives more working room while modifying the PS and allows me to lube the fan.

If you are going to use only the +12v and +5v, you may clip the other wires at the circuit board level or leave the unused wires about an inch long, gather common colors together, slip a piece of heatshrink tubing over the bundle and shrink -- it is an easy way to corral and insulate loose ends.

For the +5 / +12 volt PS, you will need the following combinations:

GREEN / BLACK Power on Switch (Use a SPST switch; a momentary switch will not work)
RED / BLACK Pre-Load Resistor (See text for recommended values and a possible substitution)
YELLOW / BLACK +12 volt source
RED / BLACK +5 volt source
ORANGE / BROWN See the Design Guide Update


I use a single common post (GND -- black) for all voltage sources. Our loads are light and we don't require separate grounds for each.

Leave 3 black wires -- switch, load resistor and common (GND) binding post

Leave 2 red wires -- 5 volt binding post and load resistor

Leave 1 yellow wire -- 12 volt binding post

Leave the green wire -- power on switch

If sense wires are present, refer to the Design Guide Update

If you expect to place high current demands on your powersupply, it may be prudent to run two wires to each binding post -- while it is very unlikely that the 18 AWG wire will overheat, there have been some instances of melted wires and connectors occurring on high demand motherboards.

As an aside, you can get 7 volts from the +5 V and +12 V outputs -- the +5 V is considered the negative (GND) and +12 the positive -- some geeks will use this combination to run their fans at a lower speed to reduce noise.



I've followed all the instructions, but the output voltage on the +12 V side is still low -- what can I do?? Many of the R/C folks are converting power supplies for the purpose of driving field chargers and are finding that voltage levels below 12 volts are sometimes insufficient to power their chargers. Read these TIPS for some options that may help increase this voltage level, provide a little theory, identify the connector pinouts found on most PC supplies and give a few troubleshooting hints.

Cut everything else off even with the board. I usually cut the power harnesses so I can keep as much together as possible. The wires remaining in the power supply should be left long and cut to length as needed. If you leave them too long, they will get in the way when boxing it up, especially if the fan is internal rather than external. Be sure that they stay out of the way of the fan blades. Also be sure to reattach the fan -- some supplies will not function without the fan attached - in any event, you need the cooling. This PS in the pictures has the fan mounted on rubber shock mounts and is extremely quiet. I will also disassemble the fan and lube the bearings while I have the PS open. Since these are salvaged, the fans have been in use for some time and normally the bearings are dry -- I use a high grade sewing machine oil from SINGER. Any light oil will work, just don't use WD40 --

These power supplies are called SWITCHMODE or SWITCHING MODE power supplies and must have a load to function -- hence the 10 ohm 10 watt load resistor on the 5 volt line. These resistors are known as wire wound or sandbar resistors and can be purchased from Radio Shack for about $0.80 each. This resistor will get hot and should have some sort of heat sink. The technique I use keeps them amazingly cool and is easy to do -- just pick the flattest side of the resistor, apply some heatsink compound (see warning above about toxicity) and attach to the case. I will usually hit the inside of the case with a file to remove any stamping flash on the ventilation slots. The switch (single pole, single throw) and binding posts can also be found at Radio Shack or other electronics supply houses.
Resistor Substitute
A viable alternative to using a power resistor is to substitute an 1157 automotive signal lamp in its place. This is a dual filament lamp and its load, with both filaments powered, is usually sufficient to maintain Latch_On and to raise the voltage on the 12v rail to an appropriate level for most needs. Your options are to solder a 5v line (red) to both positive pins on the lamp and ground the base to DC ground or to pick up a twist-lock socket when you buy the lamp. The advantage of using a socket is the ease of replacement should the lamp fail. If you don't feel comfortable with your soldering skills, it is also a little easier to work with the wiring on the socket rather than the pins on the lamp. Just remember that the socket housing is the ground and the two wires in the base are to be attached to the 5v rail. More importantly, you must be very careful that neither the bulb base nor socket housing touch any of the internal components in the power supply. These lamps may be purchased at any automotive supply store and most Walmarts.

I prefer the use of resistors since the final converted product is wholly self-contained and I have more control over the applied load, but the use of a lamp does simplify finding and installing components. It also makes a very obvious Power_On indicator!

I usually deal with on-line suppliers such as Jameco, Digikey, Mouser, etc. because we are buying in larger quantities and Radio Shack is too expensive for large numbers of items. However, you should be able to convert your PC supply for $5.00 or $6.00 dollars -- less if you have a junk box of parts. I suppose you could add an LED indicator with a 220 ohm dropping resistor to the 5v rail to show the PS is turned on, but the fan is a pretty good hint. We have had supplies running 24/7 for months without problems -- just electricity consumption.

The PS has some fairly hefty electrolytic capacitors and can still give a bit of a shock immediately after being unplugged -- let it sit a couple of minutes before poking around inside. Obviously, you can get whacked if you are inside the case with it still plugged in -- probably won't kill you, but you WILL turn it loose (never mind how I discovered this bit of information).



Peazzzz..

Saturday, March 8, 2008

Kemusykilan...siapakah Jurucameranya...

GBR...camner ni..sapa amik gambar Puteri Gunung Ledang travel balik ke Taiping ni...Phone aku sentiasa ada dalam poket sepanjang perjalanan balik...tapi ada dalam memori kad phone aku ni...

Tengok...



Peazzz...

ps...sapa dapat jawapannye ada habuan...

Konvoi...Memangkah 2 Ba'ading

PRU12...ari ni 8/3/08 tamat dah...skrg ramai yang menanti depan TV menunggu keputusan keluar, menang kalah adat bertanding...lumrah, tapi yang aku nak ajukan disini ialah aku juga telah menunaikan tanggungjawab aku sebagai Seorang Anak Malaysia...

Tapi isu kat sini sekarang ialah Konvoi 2 ba'ading berelegan...(ni mesti yang habang satu lagi tu Radang bila manireng ni....)

Saksikanlahhhhhhhhhhhhhhhhhhh......Puteri Gunung Ledang diikuti rapat oleh..Pahlawan Fedang Xray<---Felat cikit tu....



Nampak tak Puteri Gunung Ledang



Sebelum pi undi kami sempat singah di Tanah Warisan dan berposing bersama Elegan dihadapan rumah...







Saja post bebanyak gambar nak bagi Radang si Habang yang sa ekong lagi tu....









Puas posing baru la pi jalankan tangjawab......



Siap leh claim duit minyak lagi...full tank la kami isi masa perjalanan balik ke rumah masing masing...
Ni ada video life sikit konvoi tu...tapi kena pusing monitor tak pu senget kan kepala ke kiri...pasal tangkap guna handphone secara menegak...



Peazzzz....enjoy..

ps.....nak tengok TV menanti keputusan 2 & 3 tempat yg aku nak ketahui...specialy ditempat aku memangkah dan juga ditempat kenalan aku bertanding..harap-harap kawan aku tu berjaya...

Dan makan lagi....Ban Pecah..

Semalam sabtu pi Penang...since anak2 dan ibunya Isnin cuti sekolah...Ahad petang (2/3/08) jalan lagi...tujuan nak pi tinjau2 persiapan sambutan PRU12 dikawasan sekitar...dan disebalik tu pi ada ajenda tersembunyi aku...nak rikki...UHF handy yang diperkatakan oleh rakan2 lokalan Parit Buntar...terjumpa kedai yg disebut tu tapi aku kurang yakin ngan ketahanan dan keupayaan handy tersebut...okey lupakan kesah tu...sambung balik pasal ronda2 keluarga ni...since ari dah petang macam biasa lah...ambil keputusan balik ikut jalan Tanjong Piandang dan kuar ikut Selinsing and singah makan di BAN PECAH...

Tapi kali ni tak syiok sikit...tau pasal apa...terlalu lama menanti hingga hilang selera...menanti..menanti dan menanti makanan tak kunjung tiba...



Menanti....



Dan menanti....



Dan....menanti....



Last sekali selepas menanti lebih kurang 45 minit ke sejam rasanye...tiba la hidangan yg dipesan...Kari Ikan Bawal ngan Kerapu...Telur Dadar...Kangkung Goreng Belacan...tu la menu dia nak tangkap gambar pun dah gelap so makan je lah dengan hati yg menyumpah...tapi terubat gak bila time bayar...harga jauh dari jangkaan...Murah...So kalau nak kesana lagi sekali pun...mungkin sebab faktor harga saja...yang lain no komen...bab nanti ada orang radang lak..pasal dia selalu promosi tempat ni....

BAN PECAH yang tak pecah....



Peazzz....

ps...sorry gambar tak se keliar...pandangan mata...

Telok Tempoyak...Makan Lagi..

Sabtu 1 Mac petang ada tugasan kat Pulau Mutiara (Penang) dan kebetulan seisi keluarga nak ikut, deme kata boring duduk rumah..samapi san buat kerja dulu dan lepas selesai semua kerja apa lagi...hari pun dah petang, perut mula lapar...one two som...nak makan mana...at last ada pemenang, so pemenang suggest pi makan Ikan Bakar...jeng..jeng...jgn radang pasal tak ajak...program tak dirancang...Nikmatilah gambar je...makanan dah jadi...ehm...ehm.. la dah seminggu berlalu...

Menu yang dipilih oleh pemenang...tu yang baju pink...


Ni nasi lum sampai...separuh dah ikan habis diratah...sib baik order 2 ekor..



Udang tengah bersantai posing maut tu...menanti nak kuar barisssssan...



Emmmmmmmmm...sedapnye....ketam tu...bila nak mula ni...



At last...nyam..nyammmmmmmm sorry...to achik...ayah tak call achik...



Nanti lah...cuti sekolah ni diet la balik...rugi ni kalau tak makan ni...mengancam tul udang tu...hait...



Mana pi Ketam sekor tu...lari kemana lak...tadi ada empat...terjun ke laut balik ke...



Ikan aku dah nak abis dah...ikan ayah banyak lagi ni...hisssssss tak leh jadi ni...kena buat muka masam sikit ni...Ayah mesti perasannye ni...nanti dia bagi la ikan tu kat aku tu...



Ni la tempatnye dari view jeti teluk tempoyak










Kak Yong...bila hari gaji bulan ni...jom la konvoi pi tempat ni...kan kita janji ari tu...tak yah la pi BAN PECAH tak best....sini lagi best....

Peazzzz...

ps...yang parah kena bayar AYAH.... tapi puas ati...bertambah Roy lah perut ayah tu...

Tuesday, March 4, 2008

New SPENDER TH-280M

Ni lagi satu keluaran TC Group...Spender Hitam Baru...



Ni Spec dia...

- Band 144.0000-146.0000 MHz
- Dimensions H : 90 mm. W : 50 mm. D : 30 mm
- Light Weight 180 g.
- 214 Groups of DCS & 50 Groups CTCSS
- 128 Channels Free Memories.
- Stop Watch
- S-Meter Bar
- Auto Battery Save
- Duplex Function.
- Time-Out Timer
- Etc.

Nak dijadikan cerita hari minggu yang lepas ada pi parit buntar...jalan jalan dan tengok satu handy UHF sama rupa paras tapi nama je lain.

Peazzzzz.....

Sunday, March 2, 2008

Saja Nak Perangat

Ni tengok masa hari sukan SKTPM...nak balik curi tangkap gambar...

Nitro 150 Ranjer convert to Yamaha...just boh sticker.

Apamacam ada hati ka...PRGQ..Harga tanya owner dia kata RM4k plus...





Peazzz...

Matang Diserang Tiga Batalion Melayu

Thanks to Kak Yong yang mengsponsor peluru tuk serangan ini...Matang dapat ditakluki setelah berhempas pulas lebih kurang 2 jam....hehehehehe...

Acik rugi tak ikut...jangan marah...











Batalion ketiga sampai lewat...mula kata malas nak mai..tub-tub sampai in full team...

Sorry..gambar sponsor tak de...



Peazzz...